ConvaTec SUR-FIT Natura Two-Piece Convex Pre-Cut White Durahesive Skin Barrier With Tape Collar

More Information

Begin by cleansing the peristomal skin with mild soap and water (soaps should be free of oils and creams). Pat dry thoroughly. The skin should be free of any solvent or greasy substances.

ConvaTec SUR-FIT Natura Skin Barrier/Wafer Preparation

• Measure the stoma size with the measuring guide provided. Select a skin barrier/wafer with a flange (white ring) that is at least 1/2" (13mm) larger than the widest diameter of the stoma. If this size is not available, go to the next larger flange size.
• Trace the exact stoma size onto the center white release paper in the back of the skin barrier/wafer. The small starter hole should be in the center of your tracing.
• Cut along the tracing with curved, short-blade scissors. For skin barriers/wafers with precut stoma opening: Select a skin barrier/wafer with a precut stoma opening the same size as the largest diameter of the stoma. Do not enlarge the precut stoma opening. Remove white release paper from the skin barrier/wafer. Leave the outer release paper on the tape collar in place.
• Stomahesive Paste can be applied to the back of the skin barrier/wafer to further fill gaps between the skin barrier/wafer and the stoma. Allow the paste to set for one minute prior to application to the skin. (Do not spread the paste.)

How to apply ConvaTec SUR-FIT Natura Skin Barrier/Wafer?

• Center the skin barrier over the stoma. Press the skin barrier against the skin. If using a tape bordered skin barrier, remove the remaining backing paper one side at a time.
• During application, maintain gentle pressure on the skin barrier for 30 seconds to improve adhesion.

How to remove ConvaTec SUR-FIT Skin Barrier/Wafer?

Gently pull the skin barrier down, away from the skin, while supporting the adjacent skin with your other hand. To assist with the barrier removal, an AllKare Adhesive Remover wipe may be used to remove any adhesive buildup.

ConvaTec SUR-FIT Natura Two-Piece Convex Pre-Cut Skin Barrier User Manual

Customer Reviews & Questions

Reviews 0 Questions & answers 3

No reviews yet

Bought this product? Your review helps other customers choose.

Write a review

Search questions and answers Search

Ask a question

3 questions, 3 answers

1. Q

   Question: Does anyone make a 2 1/2" pre cut barrier (2 pc system) ?

   Asked by Celia B. on Jan 28, 2021 Report
   • A
     Answer: Unfortunately we do not have the product you require and so we are unable to assist you further.

     Medical Supplies Club Customer Care Store answer Jan 28, 2021

     Helpful? 0 0
   Answer this question
2. Q

   Question: my coloscopy output has suddenlly turned very acid and eats through my wafers every few hours. are there acid resistant wafers to be found? any suggestions?

   Asked by Jim J. on Jan 20, 2020 Report
   • A
     Answer: We are not medically trained to answer your query. we suggest you to consult with your doctor regarding this.

     Medical Supplies Club Customer Care Store answer Jan 22, 2020

     Helpful? 0 0
   Answer this question
3. Q

   Question: what bags fit this

   Asked by Mildred R. on Feb 19, 2018 Report
   • A
     Answer: Skin Barrier/Wafer Preparation:
     - Measure the stoma size with the measuring guide provided. Select a skin barrier/wafer with a flange (white ring) that is at least 1/2"" (13mm) larger than the widest diameter of the stoma. If this size is not available, go to the next larger flange size.
     - Trace the exact stoma size onto the center white release paper in the back of the skin barrier/wafer. The small starter hole should be in the center of your tracing.
     - Cut along the tracing with curved, short-blade scissors. For skin barriers/wafers with precut stoma opening: Select a skin barrier/wafer with a precut stoma opening the same size as the largest diameter of the stoma. Do not enlarge the precut stoma opening. Remove white release paper from the skin barrier/wafer. Leave the outer release paper on the tape collar in place.
     - Stomahesive Paste can be applied to the back of the skin barrier/wafer to further fill gaps between the skin barrier/wafer and the stoma. Allow the paste to set for one minute prior to application to the skin. (Do not spread the paste.)

     Medical Supplies Club Customer Care Store answer Feb 27, 2018

     Helpful? 0 0
   Answer this question

Write a review

ConvaTec SUR-FIT Natura Two-Piece Convex Pre-Cut White Durahesive Skin Barrier With Tape Collar

×

Overall rating *

5 stars 4 stars 3 stars 2 stars 1 star

Review title

Your review *

At least 20 characters0 / 5000

Would you recommend this product?

Yes No

Name *

Shown as first name and last initial

Email *

Never shown. Used to match your order.

City, state (optional)

Leave this empty

Please leave out phone numbers, email or street addresses and order numbers. Reviews are checked before they appear.

Cancel Submit review

Ask a question

ConvaTec SUR-FIT Natura Two-Piece Convex Pre-Cut White Durahesive Skin Barrier With Tape Collar

×

Your question *

Our product team and other customers can answer.0 / 2000

Name *

Email *

Never shown publicly.

Leave this empty

For order or delivery questions, please contact Customer Care. Questions are checked before they appear.

Cancel Send question

×